gear

Hi all, I'm back on my stock 12t pinion for the Outcast on 6s. Went for a 5 min play in the park and when finished noticed the centre diff cog was super hot. Should this be the case. Was a lot of wheelies and front wheel spinning in the air. My cogs seem to have a tiny bit of play between them...

After i have shim the diff with two 13/16 shim The pinnon gear still very loose, i tried to put two 8x12x.2 and the fit is perfect and after 1 pack i reopen my diff and the shim is completely trash ?

So a friend of mine gave me a motor fan, so i thought: now i can run my 16t pinion with 6S without the motor getting too hot. Is the only problem with running a bigger pinion the temperature? Or also resistance and-or other forces on the motor? And what temp is the maximum to reach for a...

I was looking at the pinion wheel and found it like this. It seems to have a little offset. Is this normal? And if it is, is it better in terms of efficiency and lifespan?

First question, what is the stock gearing for an Arrma typhon? I believe it seems to be 13/50 reading around but correct me if im wrong. I bought my Typhon second hand and while it handles and drives great, its honestly disappointingly slow compared to my 1/10 traxxas bandit. At top speed I can...

Hey all, I've had my kraton for a couple years and have done it up tastefully, and love it! Just recently picked up the the Senton BLX 4x4 and instantly fell in love. Heard a couple squeaky bearings and replaced ALL of then with Fast Eddie's sealed. Took it out again today (first time on...

Before I put the torch to my truck, is everybody running the 16t pinion?

On my notorious im seeing 52-56 mph stock pinion 6s what is everyone else seeing. Only videos I have found seems to be down near 46mph

Do i need to buy a new pinion gear for the bigger shaft on the motor or just drill it out?

Before I start trying gears, this 4s vs 6s is new to me. So, if the stock 12 tooth is good starting point for 6s, then what would be the same good starting point for 4s batteries? Same pinion (seemed slow compared to my 8th scale buggy with 1900 kV motor), or the larger 14 tooth?

I have a V2 Kraton and although it has been great, I am looking to get more out of it. I am sort of a noobie when it comes to this and am running my Kraton basically bone stock with the only upgrade being Backflip Tires because the original ones ballooned so much they spun off the wheels, and my...

Got my Kraton last week. The top motor mount screw just keeps popping loose towards the end of one pack. Running 4s 5000mah 50c, ESC punch at 8, doing jumps. Using blue Loctite right now, have had to remesh it about 3 times already. I also switched to slightly longer screws from an axial...

So this is what every diff I have ever opened right out of the box. This is why we go through our “RTR” vehicles.

I was on rc planet and saw a 57t hd 0.8 mod 4x4 spur gear INSTOCK and a 15t penion gear and the site said it was for the granite and the mega has anyone else installed this set up and if so hows it going for you please help since I cant buy the stock gear I figured I would check this set up out

I recently installed a traxxas 12t brushed motor in my fury and found the plastic spur gear has a section of teeth worn out after using it twice. Is there an aluminum spur gear i can replace the plastic one with? Or do i just replace it with the same 87 tooth plastic spur gear? Anything else i...

Hey guys I wanted to run the Talion one last time before I tore it all down to replace the bearings with Fast Eddy’s ones- and I took it out in the street on 6s and after just a few seconds the rear diff screamed. Well, I tore it down and what a mess was inside the diff housing! All greasy and...

i put in the 16 t pinion for Arrma Outcast and it goes way faster but sometimes when i smash trigger at slow speed it sounds and feels like it skips a gear and just cogs out and doesn't move. is my mesh not good or is it a side effect from higher gearing?

My granite voltage sounds like its grinding gears. It can still go forward and reverse. It's just not going very fast. It's a new truck so I can't find much on it unfortunately, so any help would be greatly appreciated!

Hi all, I noticed crappy pinions lead to the fast destruction of spur gears. So, I just picked up a tekno rc pinion gear that was a decent price, looks pretty nice.... Robinson racing pinion gears surprisingly aren't good, they are super soft! I bought one of these...

I run 6s on my Kraton and Outcast. And run them hard bashing and on pavement where I am hard on the throttle for long periods of time. My question is, do the spur gears wear out? Thinking about buying a new one just to compare. I will put my digital calipers to it to compare old vs new...