gear

So I recently decided to restore my older gen 1 Typhon that I knew had a few issues. While tearing apart the rear diff I noticed that the rear input gear had snapped a couple of teeth off. Easy enough fix, I guessed. Let's just order one. I ordered Arrma part #AR310468. The exact same as the...

Hey guys im wondering how much i can up the pinion to get a little more speed but still be able to bash offroad without over heating anything .. i have the v3 i believe it comes with a 12t pinion stock ? I also have put on a set of truggy tires which are a little smaller then stock and lighter

Should I put a shim behind (MAIN INPUT GEAR 10T SPIRAL #AR310498)? I cant find answer any where!

In need of a new spur gear, are there any spur gears out there made from metal? The stock plastic one didn’t last very long

I have the stock spur running a 22T pinion. Only hit 57mph???? Maybe there tarmac was a little wet and slippy and very cold out 2-4degrees. However I wads wondering about strengthening the spur gear to a hardened steel on passably a 46T. Any suggestions which one to get or where from. Im UK...

Hi guys, Third run on my outcast today and it's first on 6s. Was very happy until the pinion gear grub screw came loose and the gear slid towards the end of the motor shaft. I assume the motor shaft flat does not extend all the way to the end, to stop the gear flying off in such situations...

I was changing my pinion gear when I noticed that I have a hard spot when turning over my motor by hand. The car was running fine when I started working on it. I was checking gear mesh and notice the motor was real hard to turn over it will turn over by gets to a tight spot u can get it to keep...

Can u use a 25 tooth Pinion with the 50 tooth spur?? I did and the teeth on the spur broke off. Do the numbers of the gear don’t match or did I set the mesh wrong. Someone help pls

Which pinion gear are you guys using with your stock esc/motor combo? I am still using the stock pinion gear that was installed out of box, but I would like to get some more speed. Thanks guys!

Hi everyone I'm new to this forum, I just purchased a Fazon and charged up the 3S batteries put them in the truck and went to give it a blast and it won't go at all, it just makes a grinding noise, I can see the two gears spinning and meshing together but it only makes a loud grinding sound...

v3 kraton with backflip tires what pinion size is everyone running without overheating?

Hello Guys, I just wanted to ask about the gearing that is seen at the speed card of the Granite Mega truck. I know the 48dp already which is the pitch size. But I could not seem to find what 0.8 Mod means. Thanks in advance.

Hello hobbiest I figured I would share what I broke a week ago on 3s. Not running 3s for bashing anymore because I ended up with one wheel spinning and pulled it a part and found this

is it a easy way to remove end replace the rear input gear?

I just blew a few teeth in my DEX8T front diff spur gear (spiral cut 43T). Part# TDR310518 I can get a Talion spur gear 43t spiral cut part# ARA310497 Visually (over the internet) they look identical. Can anyone please confirm? Any chance someone sorry swapped the parts or has access to a...

I hear a lot of stories about people busting pinions and/or shredding spur gears on the 1/8 line up due to pinion failure.. Should I be upgrading pinions immediately on a brand new truck to prevent more damage later on?

So per my other post, decided to grease spur gear only (not pinion). Used coffee wooden stick (worked perfect), Q-tip, and Phil Wood waterproof grease. Cracked stick in half and left me with sharp edge to easily get in between teeth. Applied very carefully not to glob it in. After entire...

Hello I recently upgraded my Granite BLS with metal gears in the tranny and I also upgraded the spur and pinion gear to the same ones that come stock on the BLX. The issue I'm having now is the only way my tires spin is if I pick up the rear end. If the tires are on the ground the pinion n...

Arrma please sell us smaller spur gears! Plastic ones too so we can test ratios cheaper!

I'm looking for a smaller spur gear to put on my typhon so I can go bigger on the pinion. I know that the Team Durango 46T is on back order till at least the end of the summer( that's what a couple of companies told me). I've been looking at other ones that would be compatible with my typhon and...