motor

Granite 3S BLX Bearing at the end of the motor shaft inside the motor housing broke today, causing the shaft magnet thing to rub all over the inside of the almost circuit board looking material that it’s supposed to spin around. I’ve got most of this black soot off the shaft itself but...

Hello im new to RC. Purchased a kraton 6s v4 a couple of months ago... I Absolutely love it ! Its kept me occupied through the lockdown anyway. Just looking to start to upgrade a few things. Any advise on motor and esc upgrades ? Also where can I get a decent motor heat sync fan and aliminum...

Debating this motor and esc upgrade MOTOR: 4-POLE SENSORED BRUSHLESS, 2028-800KV http://www.castlecreations.com/en/motor-4-pole-sensored-brushless-2028-800kv-060-0064-00 ESC: MAMBA MONSTER X 8S, 33.6V http://www.castlecreations.com/en/mamba-monster-x-8s-33-6v-esc-010-0165-00 Motor Mount...

I got the truck 3 days ago and is was a bit dirty so I wanted to take out the electronics so I can clean the inside, firstly that red block was really jammed in but that came out but the motor unit just will not budge, I've looked up videos and they just slide out with ease. Am I doing something...

After a few jumps and tumbles the 3 motor cables on all of my RCs flop around and end up askew in a bundle even when using the built in cable runs, sometimes with the bullet pins half pulled out Does anyone know of an aftermarket cable tidy that will keep my ESC and motor cable straight and in...

Hello everybody, I finally got a brushless motor for my Granite Mega. I have a question about the pinion gear though. Is this the right gear for this motor? Something doesn't seem right here.

I have a Kration 8s it came with the spektrum 160 esc and 1250kv motor. just last night it started giving me issues. I don’t have any throttle control UNLESS I take the motor B line out of the esc then it starts to work. When I pull the motor b cable out the esc boots up normally. With the...

Two motors, the built in washers failed. Hope arrma soon makes them thicker at that part! For now think I am going to start adding something underneath the motor to support it.

Using my 4s outcast this morning and after one jump I could hear a rattling, so took everything apart and singled it down to the front motor bearing being worn out. I pulled it out and replaced it put everything back together. Now when I go to use it I have power when I lift my RC off the...

Gotta think, that I got a lemon. My wife bought me the Senton 3s for Christmas. It's been in a state of constant repair ever since. The front bumper failed within a few days. Replaced with a T-bone racing bumper, well worth it. Couple weeks later, the motor starts cogging. Horizon sent me a...

I am planning on buying new, bigger, heavier tires for my kraton - will I need to gear down to an 11T pinion? I already have a Hobbywing motor heatsink and fan

About 3 Hours ago, I was driving my Arrma Kraton 6S Blx on 6S LiPo (temperature outside: about 10°C or 50°F), but suddenly, it stopped and the motor was kinda jammed up. I then took the body off and noticed a burnt smell.. Oh god... I suspect that it overheated as the temperature outside was...

Hi guys I’ve just got the infraction and keen to get a heatsink and fan combo for it to keep the motor running cool as much as possible. does anyone have a link to a set up I can buy for it please ? It’s the standard motor in there. Heatsink and either a big single or dual fans wanted for...

Hi all first rc car so no experience at all. I'm having an issue where the motor spins but will not drive the wheels. Wheels spin manually and are all connected which suggests the driveshaft and diffs are are ok. The power isnt transferring from the motor to the driveshaft but I have no idea...

Hi all, first time poster. Recently upgraded my Raider battery to a FLOUREON 2S2P 7.4V 6200mAh 40C. Gave it a blast for around ten minutes and was loving it until smoke started appearing from the motor - never a good thing. Car now seems underpowered (unless the battery had drained) so suspect...

I just noticed this, and I have no idea how it happened. Apologies because I don’t know the correct terminology, but will this cause any damage? It’s driven normal and I only saw this being bent while cleaning. Thanks in advanced.

My 4s kraton keeps having unfortunate issues.. i tought i only had 2 stripped screws after i nose landed when my screws had loosen up(treadlock failure). Turns out i have 3 stripped screws:/ i have 2 holes left for my adjustable motor mount only.. i have a hard time emptying a baterry without...

My kraton 4s motor today stripped two of is mounting holes i used to mesh my 13t pinion i was pushed to use the mega adjustable motor mount that i was about to sell:/ because with the stock mount i was not able to find the right holes anymore. All of that because of the stupid blue locktite who...

I recently ordered a few acer ceramic bearings for my arrma kraton 4s motor bearing still a bit concerned because of the last motor who blew up on me. Did i do the right choice? I never heard of acer racing before what are the benefits of the ceramic bearing also? I only knew a few ones

Im really starting to be really sad.. i did not have any parts breakages yet but i just had a lot of bad luck with my first arrma car. Now my motor bearing completly exploded killing my motor for sure because i saw winding inside the can being in place it should not be in:c