pinion

So a friend of mine gave me a motor fan, so i thought: now i can run my 16t pinion with 6S without the motor getting too hot. Is the only problem with running a bigger pinion the temperature? Or also resistance and-or other forces on the motor? And what temp is the maximum to reach for a...

I was looking at the pinion wheel and found it like this. It seems to have a little offset. Is this normal? And if it is, is it better in terms of efficiency and lifespan?

Hi guys, I have an typhon 6s v3 (i run it on single 3s). There is an (long) story behind that but it doesn't matter. So i was wondering, the manual says the 16t pinion is only for high speed runs and not for start stop driving bashing, etc. since it is bad for your motor. But the V4 typhon...

Hi all, After only 3 packs, my new Kraton's grub screw backed out of my pinion and took a bite out of my motor mount. Luckily, I don't see any major structural damage even though I didn't notice until the end of the run. My question is, what kind of thread lock is recommended? I didnt see...

Before I put the torch to my truck, is everybody running the 16t pinion?

So in my homemade bigrock/granite conversion I'm running a 1900 kv motor with a 26 tooth pinion on 3s. It runs like a raped ape. I'm happy with it but I'm not sure when the weather actually makes it too the plus side of 0* whether or not its gonna overheat or not? Whats your thoughts?

Do i need to buy a new pinion gear for the bigger shaft on the motor or just drill it out?

A have a factory v3 kraton that i wanna drag race i have changed to smallest road rim/tires that will fit and added biggest pinion i can fit next i am thinking of locking center diff and going down to 43 tooth main diff gear but haven't done

So took the motor out of my brand spanking new Kraton to swap the pinion. I wil NOT come off. I have tried heating it, soaking in solvent, prying it, Even tapping the motor shaft from the top while the pinion is in a vice. I have now tore up the top of the motor, and still no closer to getting...

I recently broke the stock pinion and replaced it with a Robinson 12T mod1 pinion from the LHS. Ive read these pinions sound different but Im wondering if this sounds normal? The spur gear is centered on the pinion and I believe the mesh is proper. Im not having any heat issues, it just seems to...

i put in the 16 t pinion for Arrma Outcast and it goes way faster but sometimes when i smash trigger at slow speed it sounds and feels like it skips a gear and just cogs out and doesn't move. is my mesh not good or is it a side effect from higher gearing?

Hi all, I noticed crappy pinions lead to the fast destruction of spur gears. So, I just picked up a tekno rc pinion gear that was a decent price, looks pretty nice.... Robinson racing pinion gears surprisingly aren't good, they are super soft! I bought one of these...

Hey guys I just purchased a authentic Armma 22T pinion fear for my Typhon. Can I install this with the stock 50t spur? I have the stock motor and esc. Jon-

I have a tekno 15 tooth pinion due in tomorrow so I figured I'd go out today and see how much speed I could squeeze out of the stock 12 tooth pinion. 2018 Version Outcast Deleted wing and lowered ride height to where the lower a-arms were parallel with the tarmac Best pass of the session was...

Hi guys, Third run on my outcast today and it's first on 6s. Was very happy until the pinion gear grub screw came loose and the gear slid towards the end of the motor shaft. I assume the motor shaft flat does not extend all the way to the end, to stop the gear flying off in such situations...

I was changing my pinion gear when I noticed that I have a hard spot when turning over my motor by hand. The car was running fine when I started working on it. I was checking gear mesh and notice the motor was real hard to turn over it will turn over by gets to a tight spot u can get it to keep...

Which pinion gear are you guys using with your stock esc/motor combo? I am still using the stock pinion gear that was installed out of box, but I would like to get some more speed. Thanks guys!

v3 kraton with backflip tires what pinion size is everyone running without overheating?

Hello Guys, I just wanted to ask about the gearing that is seen at the speed card of the Granite Mega truck. I know the 48dp already which is the pitch size. But I could not seem to find what 0.8 Mod means. Thanks in advance.

I hear a lot of stories about people busting pinions and/or shredding spur gears on the 1/8 line up due to pinion failure.. Should I be upgrading pinions immediately on a brand new truck to prevent more damage later on?