raider

Looking for some instructions installing the roof plate . No hardware came just the plate. Does it mont to the old one or do I need to order some other part?

Hey all, I've made a forum post in the Build Logs about my journey into RC's with my Raider. I also posted a lot of information about upgrades and mods I did to my Raider including part numbers. Hopefully people find it helpful! I will be updating it periodically as I make changes to my Raider...

I am making this post to document my journey into RC's with my ARRMA Raiders. When starting off I found it difficult to find posts about the Raider due to it being a less popular vehicle. With ARRMA's 1/10th line in general there is little available for help and photos for guidance. Therefore...

How do I switch over so my Raider BLS can run on a LiPo. Thanks!

I have had my Raider for about 7 months. I have used It about 20 times. Had loads of fun. But then it would run a short distance and stop. I recharged it and It did the same thing. It didn't seem like a mechanical problem so replaced the 2000 mah battery with a 3000. And it ran faster and...

Hey everyone. I've had a problem with my stock dogbones chewing up my out drive cups. I was wondering if anyone has tried HPI RS 4 MT 2 ( tower hobbies part #lxfyu8)? They are a tad longer at 86mm, which I'm assuming is pin to pin and not end to end. I'm thinking the extra 3mm might help me...

Hi all, I recently upgraded from my BLS Raider to the latest BLX XL Raider and started to notice that both of my Venom Hardcase 2s 30c 5000mah LiPo batteries are starting to be unbalanced after running. I use a SkyRC B6AC+ v2 charger and when I plug the batteries in after running the first cell...

What's with the black icons on the Raider forum? Only it and the ADX-10 appear that way. Does that mean the Raider is going the way of the ADX-10?

Has anyone bought and fitted the Arrma Metal roof on a Radier 1/10 Brushed? I ordered this from Tower Hobbies: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXEAUU&P=7 Problem is the original plastic roof has tubes through the underside that allow it to be screwed in from either side of the...

I have a brand new 2016 model Raider BLX XL after upgrading from my old Raider BLS. I've got a BLX85 fan (AR390249) and I wish to mount it but I'm not entirely sure how to do it. Is there a visual guide or a video for mounting the fan. Also will this mean that my ESC will no longer be...

What would it take to convert my Mega XL to brushless and run on 3s? Thinking just a motor and esc. But which motor? Don't know about KV and all that.

Hi, I have to change my rear tires on an ARRMA RAIDER MEGA 2wd 1/10. I don't want to put the original ones. So i run on an exterior dirt track (little bit of sand and hard soil). I take a look on the Sidewinder, Copperhead or Sand Scorpion. I don't want to have a tire like the SLINGSHOT. So...

Hello arrma community. I have a raider xl that i installed a 2200kv motor an esc combo in, beefed up rear suspension ,medal gears in the trans an foam speed run wheels an tires , motor an esc fans to keep it cool. Cap pack etc..Im running 34t pinion 48t My question is can u use a traxxas spur...

I was thinking.. What if I took the front arm pieces off my 1/10 raider and put them on my 1/8 with bigger tires on the rear it would look cool and might go faster? It would defiantly flip over easily. What are your thoughts guy? I might try just for fun. Will let you know how it goes lol.

So I picked up a Raider XL BLX from the LHS for some on track bashing mostly, but just an all around basher. Only chose the Raider XL because 2wd sounded like fun and I've always wanted a buggy. Anyway, out of the box the thing ripped pretty good. Shocks looked like junk and the first time out I...

Share your RC wrecks / damage pictures and videos here!

Anybody know of any upgraded bell crank or servo mount for the Raider? My steering is all new from the steering blocks all the way in, including new metal tie rods, and there is more play than I would like. Whole rack moves 1/4 -3/8" before servo starts turning when moved by hand. Am I...

Hello, I am new to this forum, I do not own any ARRMA rc's YET. But I have had my eye on the Raider XL BLX for about a year. However after watching and reading many reviews, I determined it wasn't quite worth the money. I was seeing far too many disappointed folks. I heard of electronics...

I have the Arrma Raider XL mega, I disassembled it I need help with the front end reassembly and the servo area. Any phots or videos would be of great help. THE MANUAL IS OF NO HELP Thanks

Whats a good gearing setup for the 2000kv 4075 motor? I'm thinking about modding my raider XL with this motor for speed runs... Only cause i found it for a very low price on Tower Hobbies website.