Useful Arrma Related 3D Print Stuff I've Uploaded to Thingiverse

[jondilly1974]

Just added the following to the first post:

Due to popular demand I've added adapter plates that now support 2x40mm fans for the Kraton 8s heatsink, see link below**​

​

Arrma Kraton 8s heatsink 30/40mm fan adapters​

https://www.thingiverse.com/thing:4460604​

Allows you to install 2x30mm or 2x40mm fans on the Arrma Kraton 8s Heatsink replacing the stock 50mm fan​

I will be printing this one for sure ????

 

[Rainger40]

You guys have a link to a good 1/10 scale heat sink 30 to 40 mm fan mount?

 

[suchtragedy]

You guys have a link to a good 1/10 scale heat sink 30 to 40 mm fan mount?

I uploaded this one a while back, let me know if it works out. I didn't really advertise it because I had no way of testing it myself at the time.

https://www.thingiverse.com/thing:4579929

 

[Rainger40]

I uploaded this one a while back, let me know if it works out. I didn't really advertise it because I had no way of testing it myself at the time.

https://www.thingiverse.com/thing:4579929

I was checking out your t-verse yesterday and I think I collected this haha. I’ll definitely let you know when I get around to it, but it might be a while because I’m going to be down for a while due to shoulder surgery come thursday.

 

[suchtragedy]

Added the following to the first post:

BLX185 ESC Mount for Arrma 3s Vehicles
https://www.thingiverse.com/thing:4612362
This adapter plates allows you to shoehorn the larger BLX185 ESC into the Arrma 3s and 4s vehicles. This mount fits on top of the stock receiver box and includes a place to mount the power switch. PLEASE NOTE: This will not work with the Typhon 3s due to it's low profile body (ESCs cannot be mounted on top of the receiver box, there's no room)

 

[suchtragedy]

Added to the first post

50cal Ammo Box Lipo Organizer Tray
https://www.thingiverse.com/thing:4615986
Each set of (2) trays is designed to sit in the bottom of a standard military style 50cal ammo box. The total amount of slots for a pair of trays is (8)45x60mm which should fit most 3s-6s RC car sized lipos and (4)28x60mm which fits most 2s RC car sized lipos.

 

[suchtragedy]

Added additional adapter options for the fan adapters, updated description in 1st post.

Aftermarket Fan Adapters for RC Car ESCs :
https://www.thingiverse.com/thing:4503682
These fan adapter plates allow you to replace stock ESC fans with a larger sized 30mm or 40mm fan with a higher rpm/cfm for better ESC cooling. The adapters are designed to sit on top of the ESCs without having to remove the ESC cover plate.

Adapter Options:
- 25mm to 30mm (fits BLX100/120/Max10, etc)
- 35mm to 30mm
- 35mm to 40mm
- 35mm to 40mm w/ embedded M3 nuts


Example pics for reference:

 

[suchtragedy]

Added the following to the first post:

RC Wheel Balancer (uses Arrma 6s rear hub assembly)
https://www.thingiverse.com/thing:4643011
This is a RC wheel balancer I created that basically is a stand and to it you mount an Arrma 6s rear hub with axle/bearings/hexes. With the 6s rear hub you will be able to balance 17mm hex wheels but I've also included adapters that can be quickly mounted so you can balance 12mm hex and 14mm hex wheels.

 

[Rcproponent]

Added the following to the first post:

RC Wheel Balancer (uses Arrma 6s rear hub assembly)
https://www.thingiverse.com/thing:4643011
This is a RC wheel balancer I created that basically is a stand and to it you mount an Arrma 6s rear hub with axle/bearings/hexes. With the 6s rear hub you will be able to balance 17mm hex wheels but I've also included adapters that can be quickly mounted so you can balance 12mm hex and 14mm hex wheels.

View attachment 107956

View attachment 107957

View attachment 107958

View attachment 107960

View attachment 107959

You got the gift man, very nice ??

 

[Doom!]

That's a pretty cool setup!

 

[suchtragedy]

Added the following to the 1st post:

Flysky FS-GT5 Radio Upgrades (thumb steering, menu knob replacement, aux channel knob replacements)
https://www.thingiverse.com/thing:4647728
A few designs I made to improve the Flysky FS-GT5 radio to make it more user friendly, imo. Designs include thumb steering easy add-on, an easier to use menu knob, and Aux5/6 knobs that makes it easy to adjust with 1 finger (works great with Aux6 for rear wheel steer while driving.)

 

[suchtragedy]

Just added the following to the 1st post.

Arrma 4x4 Steering Crank Cover :
https://www.thingiverse.com/thing:4654772
This cover is designed to keep larger rocks/debris that falls in from the top and gets stuck in the steering crank for Arrma 4x4 vehicles (Mega/3s/4s)

The steering crank cover is now a part of a set along with a center driveline cover.

Arrma 4x4 Driveshaft & Steering Crank Cover Set:
https://www.thingiverse.com/thing:4654772
This cover set is designed to keep larger rocks/debris that fall in from the top and get caught in the center driveshaft or steering crank for Arrma 4x4 vehicles (Mega/3s/4s) with two options to pick from to accommodate both the short wheel base (SWB) and long wheel base (LWB) chassis.

 

[Hammer Down]

Added the following to the first post:

RC Wheel Balancer (uses Arrma 6s rear hub assembly)
https://www.thingiverse.com/thing:4643011
This is a RC wheel balancer I created that basically is a stand and to it you mount an Arrma 6s rear hub with axle/bearings/hexes. With the 6s rear hub you will be able to balance 17mm hex wheels but I've also included adapters that can be quickly mounted so you can balance 12mm hex and 14mm hex wheels.

View attachment 107956

View attachment 107957

View attachment 107958

View attachment 107960

View attachment 107959

You sir, are the king ? of 3D printing!
???

I need one of these @Dutch ?

 

[suchtragedy]

You sir, are the king ? of 3D printing!
???

I need one of these @Dutch ?

I am just a simple man trying to fix annoying problems without spending money on stupid stuff like dust covers all the time LMFAO

 

[Hammer Down]

I am just a simple man trying to fix annoying problems without spending money on stupid stuff like dust covers all the time LMFAO

I truly appreciate you efforts! ?

 

[Malice]

@suchtragedy Printing your 2-piece skirt now. I hope it fits. I've put on a little weight since March. Printing in Yellow PETG. I'll throw up a picture when they're done. Thank you for making those available to all. I've only made one thing and uploaded to thingiverse, but it isn't rc related. I doubt it gets a single download!

 

[Malice]

Fronts in progress. This gyroid infill is gorgeous.

 

[suchtragedy]

Gyroid infill aka ramen noodle brick infill ?

 

[jondilly1974]

My only issue with gyroid is the shake of the bed. I need a better printer someday.

 

[Malice]

My only issue with gyroid is the shake of the bed. I need a better printer someday.

I looks like it's having a seizure or being electrocuted.

Ran into my first print bed size issue. Im going to either remove this overature textured surface or print this on my other printer. Ughh it is so dialed in for tpu right now im probably not going to touch it. I'll have to figure that out and print the rear sections maybe tomorrow.