Kraton "Monster Mojave" Kraton XL build

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Finally got around to building a bulletproof rear diff with M2C cups and installing M2C driveshafts...
Now I got to do the fronts!
20221113_211049.jpg
8F4941D9-4C60-4DE6-AA48-B56324EB6899 (1).jpeg
 
Finally got around to do some wrenching today. But I forgot to take pictures. 🤷
I rebuilt the front diff with the last of 3 Arrma alu diff cases, M2C diff cups and piano wire diff cup pins. I also put in the M2C front drive shafts and replace the outer axle shaft because I stripped the screw inside of one a long time ago and never got it out. I went through the whole truck and tightened/ Locktite on anything loose. Then I moved the battery tray back so the truck stops nose diving on me on jumps.
Prior to all of this I broke a front tie rod. I did a "tie rod mod" to keep it from happening again. I got a set of 4mm rods instead of the factory 3 mm rods. I drilled out the tie rod ends to fit. I haven't had much time to drive it since because the front drive shaft popped out on the first run and messed up the stock diff cup but so far so good.
20221124_164250.jpg
20221126_130648.jpg

Updated build list:
[ ] Arrma Kraton 6s EXB roller
[ ] M2C chassis
[ ] M2C Front and rear chassis braces
[ ] M2C Rear shock tower brace
[ ] M2C Front and rear shock towers
[ ] M2C Blatterless shock caps
[ ] M2C deltron shock bushings
[ ] M2C Front and rear tool steel hinge pins
[ ] M2C Diff output cups (all 3 diffs)
[ ] M2C Front drive shafts
[ ] M2C Rear drive shafts
[ ] Hot Racing Front diff case
[ ] Hot Racing Rear diff case
[ ] Hot Racing rear tower to tower support
[ ] Hot Racing front upper brace
[ ] Hot Racing front hub housing
[ ] Hot racing front hing pin blocks
[ ] Hot Racing rear hinge pin blocks
[ ] Hot Racing Steering servo mount
[ ] Hot Racing fixed servo arm
[ ] PPS Motor mount
[ ] PPS Center diff housing
[ ] Arrma aluminum diff cases (all 3 diffs)
[ ] Fast Eddie's sealed bearings kit
[ ] Stainless steel hardware kit
[ ] JBI 20mm hub extenders
[ ] Proline 3.8" tires
[ ] Reef's 555 servo
[ ] Treal 7075 Aluminum steering rack
[ ] Castle Creations MMX 8s ESC
[ ] Castle Creations 1717 1650kv Motor
[ ] Custom motor fan mount
[ ] Duel Yeah Racing fans
[ ] Arrma Mojave EXB body
[ ] Arrma Mojave body mounts
[ ] T-Bone front bumper
[ ] T-Bone rear bumper
[ ] 4mm front tie rods
[ ] Dumborc X6 transmitter and radio
 
Last edited:
The only things left to do now is upgrade the center drive shafts, upgrade the center chassis brace with a Custom RC Racing Aluminum brace and upgrade some of the 6061 Hot Racing parts with 7075 parts from M2C, Vitavon, Treal or Basherqueen. I want to upgrade the fans but it's a basher, not a speed run truck. I also want to change the body out so I can use 6s Backflips. Probably going to pick up a Fireteam body eventually. However, my next purchase for it will be some high end 4s packs, as I am still running two 3s packs at the moment.
I can't believe I have over 2 years into this build now.. Time flys!!!
20221210_092753.jpg
 
Last edited:
Old Thread: Hello . There have been no replies in this thread for 90 days.
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.
Back
Top