Moonstone's winter builds/rebuilds

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Messages
1,192
Reaction score
3,292
Location
Ontario, Canada
Arrma RC's
  1. Fireteam
  2. Granite
  3. Granite Mega
  4. Infraction
  5. Mojave EXB
  6. Nero
  7. Notorious
  8. Typhon 3s
So this isn't a typical build thread.
More of a build/rebuild journal.

I've been in the hobby for about a year now but have had a blast Bashing, Building, and reading posts on AF.

Over the winter I will be rebuilding and modding 8 vehicles (will probably end up being more) to various degrees. This will be my first time doing most of these things so if you want to give advice I will try not to be offended.😭

So let's get started on a full tear down and rebuild of my son's Granite.
Here it is after our last bash for the season. Also our first time at a skate park 😂

IMG_20211204_115712.jpg
IMG_20211214_135451.jpg

I think I remembered how it goes back???

Bearings were all in rough shape.
IMG_20211215_133710.jpg

Opened each new bearing and packed it with grease. Hopefully this helps in case they get wet.

IMG_20211215_133724.jpg

Also found a crack in the chassis. I ordered a replacement but will try to fix it with JB weld. Roughed it up with sandpaper first to help adhering.
IMG_20211214_153919.jpg

IMG_20211214_153456.jpg

After epoxy
IMG_20211215_194254~2.jpg

IMG_20211215_194305~2.jpg

Steering rack installed. New bearings and bushings
IMG_20211216_135854~2.jpg

Front suspension done-ish

IMG_20211216_193323~2.jpg

To be continued....
 
Last edited:
Dope I’m the middle of maintenance pm on a limitless and infraction and a new build.
plus I got the kraton exb for Xmas so I’ll be getting that ready I want to be ready for riding season!
Nice, 👍 I was so close to buying a limitless during the summer but a great deal for an open box Infraction came up and I couldn't pass. Are you going to do a build thread?
 
So far so good.
Still trying to figure out what I like using best to clean. Tried simple green, baby wipes, and regular dish soap and water.
IMG_20211217_170702.jpg

Also ended up adding a 0.5mm washer to each control arm pin to take up the play.
Now time to clean and fill the diffs. Main gear and input gear are a bit worn but will run them until they fail.
IMG_20211216_193347.jpg

IMG_20211217_170713.jpg
 
Last edited:
First diff cleaned and starting to fill.

My tech tip- duplo blocks are super useful. By changing the blocks I can make it long for infraction or tall for granite or make a shock stand by adding a few holes. Also great fun to test out articulating in crawlers.
IMG_20211217_202943.jpg

IMG_20211217_202659.jpg


IMG_20211217_202643.jpg
 
Chassis and diffs are done. Both diffs were maybe 1/4 full. Filled now with 20k. Also rear diff was seemed to be shimmed on the wrong side and the was play on the crown gear.
I see now why some say to completely disassemble brand new rigs


IMG_20211219_002336~2.jpg
 
Last edited:
One of my shocks looked pretty beat on the bottom eyelet so I put a larger washer to see if it works too protect it better.
IMG_20211221_143933~2.jpg

Cleaned and refilled the shocks.
IMG_20211221_144740~2.jpg

But I think I need to order new o rings. I don't know if they swelled or I don't know what I'm doing but I could not get them to seat properly. They kept bulging out on one side or another. Maybe I was going to tight?
IMG_20211221_144805~2.jpg


IMG_20211221_143933.jpg
 
So I'm waiting on a motor plate to finish my son's Granite. So started working on my wltoys. 144001 and 124017.

So a bit of a pay it forward.
My son's 144001 motor burned out.
So the the motor from my new 124017 that I got for Christmas is going into the 144001.

The 3650 (3900kv)motor and ESC from my son's Granite are going into my 124017.

Then the stock motor/esc from my granite 3660 (3200kv) is going into my son's Granite.

Then my granite will get a new 120amp esc with 3670 (2650kv)

Crazy how one burnt out 550 caused a snowball effect.

I guess I could have just got a new 550🤣🤣

So here's a few pictures of the work on my 124027

Motor removed
IMG_20211229_152840.jpg

Shaved the plastic to fit ESC down low and tight.

IMG_20211230_161520.jpg
IMG_20211230_150327.jpg


Added some diff fluid to the rear diff and grease in the front.
Cleaned motor bearings.
IMG_20211229_154630.jpg
 
Got it mostly together. Cut part of battery tray off to clear the connector.
Also cut one of the "windows" out from the body because the esc was hitting. It ended up perfect so air blows right into the fan now.
IMG_20211231_153018.jpg


Still have to figure out the best route for the wires. It's a pretty tight fit under the body.
IMG_20211231_153041.jpg

Window opening

IMG_20211231_174847~2.jpg

IMG_20211231_174904.jpg
 
Last edited:
So finished up the buggies... Mostly
Gave them both an alignment.
Only things left are install the new wing when it shows up and figure if there's any way to calibrate this goolrc esc.
Edit: Couldn't find any way to set throttle end points and having a weird brake issue. I did fix the cogging issue with it though.

Starting on the Infraction now. It's only had about 6 packs through it so it doesn't need much. I'm switching the pinion from the stock 15 tooth to an 18 tooth.
IMG_20220106_173611.jpg
IMG_20220106_173628~2.jpg

Also going to change to thicker diff fluid. I'm sure there's probably an easier way but Im just going to jump in and started disassembling until I get to the diffs. 😉
IMG_20220106_184225.jpg
 
Last edited:
So got the rear diff out and there was barely anything inside. What was inside looked like sludge.
IMG_20220109_135753.jpg
Also the main input gear looked a bit sharp and seemed to be shimmed way to loose.
I shimmed it up a bit but not sure if it's one of those things that's gonna hold forever or snap on first trip out.

A year ago when I started the hobby I thought why would anyone strip down a brand new really expensive car. Well I know what I'm doing on my next purchase.

Also I'm back tracking on my 124017 build. Esc is giving me a bit of trouble. When I go full brakes it feels like it's only on 25% . I thought maybe it's just not that strong of a brake. So set the neutral brake to 100% and it would brake hard when in neutral but would start coasting when I hit the brakes??? Ordered a blx100 to see if it's any better.
 
Last edited:
IMG_20220112_190229.jpg

Removed and worked on front diff today.
IMG_20220113_141531~2.jpg




IMG_20220113_143501~2.jpg

Front diff had a tiny bit more fluid but it still looked nasty for half dozen runs. I shimmed the pinion but I think it was a hair on the tight side. Some spots spin loose but some I can feel a tiny bit of tightness.
I haven't decided if I will just run it and cross fingers or go full ocd and take the front and rear apart again until I'm satisfied.
IMG_20220113_141608~2.jpg


IMG_20220112_190237.jpg
 
So, I wasn't happy with shimming of both front and rear diff. So took both apart and redid then. Nice and smooth now. 😁
Only other change I made was countersunk my mangled front splitter and installed 4mm screws.

IMG_20220114_145257.jpg

Infraction is now done. Only things left in the spring are recalibrate esc and put tires on. 👍👍
 
Today me and my son took apart his crawler to clean out the mud.
Also had him help take apart the new motor module and slipper clutch for his granite. Still waiting on motor plate to come next week.
IMG_20220115_105044~2.jpg


IMG_20220115_111115.jpg


IMG_20220115_120009~2.jpg


IMG_20220115_105003~2.jpg

IMG_20220115_105249~2.jpg

IMG_20220115_105304~2.jpg


IMG_20220115_115204~2.jpg
 
So today I got my granite taken apart, cleaned, and am now assembling. It's so much easier this time now that I'm more familiar. Both my diff pinions were very worn so I changed both. Used 30k and 20k fluid in the diffs.
IMG_20220115_144913~2.jpg

IMG_20220115_144919.jpg


IMG_20220117_000918.jpg

Also found a long crack in the chassis , but luckily I had a spare.

I will epoxy the cracked one to have as back up.

Only real mod I did was drill out the steering arm and pressed in small bearings. It fixed the slop perfectly.
IMG_20220116_230840.jpg

IMG_20220116_230956.jpg

IMG_20220116_231106.jpg


IMG_20220116_230840.jpg


IMG_20220115_144913~2.jpg
 
Last edited:
I got the motor module together. Using the new thicker vendetta motor mount plate and the new 3670 2650kv motor

IMG_20220117_192257~2.jpg

IMG_20220118_093711.jpg


Also recieved the new motor plate for my son's Granite. It's the same thickness as stock plate but it's thicker where the support ribs are machined. It is way lighter though. We will see how it goes up.
IMG_20220117_192315~2.jpg

Also found this nice long crack on the chassis after cleaning off all the first dirt. Luckily had a back up one. Still patched up this one with JB weld to keep as a spare.

IMG_20220118_093737.jpg
 
Last edited:
Working on shocks now
IMG_20220119_131144.jpg


IMG_20220119_232426~2.jpg

IMG_20220119_233129~2.jpg

Also jumped back to my son's Granite and realized that I didn't have the little splined pieces that goes into the drive shaft so cut down the old mega slipper to use.
IMG_20220121_143236.jpg
 
Old Thread: Hello . There have been no replies in this thread for 90 days.
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.
Back
Top