Infraction New Infraction 3s, what to do?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
Messages
1,106
Reaction score
2,990
Location
Denmark
Arrma RC's
  1. Infraction
  2. Limitless
  3. Kraton EXB
I just got a Infraction 3s, first time on a plastic Arrma, i always been on the 6s line

What do you guys look after on it, do the diff need olie like the 6s line 🤣

What to upgrade, beside a front splitter, maybe a carbon rear wing

Do they hold up for more power, 4s or 6s

Here's my
DSC_4093.JPG

DSC_4090.JPG

DSC_4091.JPG
 
Congrats on your 1st 3s! 😁

Yes, as always check the diff oil. Other upgrades OTB are the same as 6s.....bearings, servo, a center driveshaft support helps if going to 4s.

I purchased the Mega version and turned it into a 4s. The 3s drive train can handle 4s, but I do not believe it will on 6s without some major upgrades.

Happy Bashing!! 😁✌️
 
Congrats on your 1st 3s! 😁

Yes, as always check the diff oil. Other upgrades OTB are the same as 6s.....bearings, servo, a center driveshaft support helps if going to 4s.

I purchased the Mega version and turned it into a 4s. The 3s drive train can handle 4s, but I do not believe it will on 6s without some major upgrades.

Happy Bashing!! 😁✌️
Thanks 🙏

Yeah was thinking a better servo and ESC for a start , do you have any link for the center driveshaft support?

So 6s is not a good idea 😁
 
Yup, should swap right out. I forgot the 3s comes with the plastic one, my bad. I had the Mega.

I also upgraded the plastic driveshaft to aluminum. If you get the HR one, you will need their center drive support bearing.
Screenshot_20230116_082709_Gallery.jpg


Get a center brace too. I got a CF one from ramjam racing. It was specifically for the mega though, so make sure to check the length for the 3s, not sure if it's the same.
20220912_181943.jpg
20220911_200135.jpg
 
Here's what I have done to my Infraction 3s:

R6F receiver for Radiolink RC6GS radio system
Spektrum S652 servo (had laying around)
Hoons white label wheels and tires
Arrma CNC steel-geared transmission assembly, front and rear
Hot Racing aluminum diff yokes, front and rear
Aluminum center driveshaft
Carbon fiber tower-to-tower chassis brace
Carbon fiber front splitter and rear winglets
3D printed aero chassis panels
GNSS GPS mount

A lot of what I have done is for durability, and other items are just for appearance.
 
Arrma CNC steel-geared transmission assembly, front and rear
Hot Racing aluminum diff yokes, front and rear
Aluminum center driveshaft
Yes, I did this too. I think I got the idea from you! (y) 😁 ✌️
 
Just ordered a hot racing center shaft and bearings for it 😁

And also ordered a radiolink r6f, already on the radiolink so that's easy 😊

Also ordered those CNC metal gears for front and rear

Thanks guys for all the help 🤠
 
Yup, should swap right out. I forgot the 3s comes with the plastic one, my bad. I had the Mega.

I also upgraded the plastic driveshaft to aluminum. If you get the HR one, you will need their center drive support bearing.
View attachment 270568

Get a center brace too. I got a CF one from ramjam racing. It was specifically for the mega though, so make sure to check the length for the 3s, not sure if it's the same.
View attachment 270569View attachment 270570
Is there no long wheel base driveshaft? I'm supprised the short one worked.
 
Old Thread: Hello . There have been no replies in this thread for 90 days.
Content in this thread may no longer be relevant.
Perhaps it would be better to start a new thread instead.
Back
Top