Kraton Throttle and Motor Issues on Keaton 6s

[sipes190]

I’m sure many have had this issue So I just took my Keaton 6s out after not using it for a couple months so I charged my batteries and it was working fine for about 4 minutes then it just came to a stop with no throttle inputs working I thought maybe it was just my batteries so I changed it out for a newer set and it won’t even do start up beeps or anything the esc fan spins motor fan spins I checked bullet connectors to motor hense why the wire shielding are ripped back I was checking to see if a bullet connector had come un soldered they are all still connected though I am really stumped on this one ( I have had an issue in the past with the top faze/ motor wire did disconnect I resoldered it and it has been working since then till today any tips helpful thank you

This is the video for my question

 

[N.Mango]

Stupid question but..
Did you check the connection from the ESC to the RX?

 

[332_RC]

You change your transmitter batteries?

 

[sipes190]

You change your transmitter batteries?

No I didint change the batteries in my transmitter/remote just the batteries in the car

 

[332_RC]

No I didint change the batteries in my transmitter/remote just the batteries in the car

They might have ghosted you, been a couple months.

 

[sipes190]

Stupid question but..
Did you check the connection from the ESC to the RX?

Sorry I’m not very good with like the wording of things when you say RX your meaning the connection from the esc to the thing that’s in the sealed case directly across from the esc

 

[N.Mango]

Sorry I’m not very good with like the wording of things when you say RX your meaning the connection from the esc to the thing that’s in the sealed case directly across from the esc

Yes that thing.
RX/receiver

 

[sipes190]

They might have ghosted you, been a couple months.

Wouldn’t it not work though to turn the wheels if the remote battery’s didint have enough power

 

[sipes190]

Yes that thing.
RX/receiver

I have not checked that I will do that right now

 

[sipes190]

I have not checked that I will do that right now

It seems ok no obvious broken wires or anything unplugged

 

[N.Mango]

It seems ok no obvious broken wires or anything unplugged

View attachment 408097

since you have it out, maybe unplug it and plug it back just to make sure.

 

[sipes190]

I just did that I unplugged both and re plugged them in there is a green light on the RX when it’s powered on and still the blinking green light on the esc

 

[sipes190]

Only thing I can think of besides something is just cooked is this bullet connection I re soldered a while back could be an issue but the connection is strong and it doesn’t budge

I just did that I unplugged both and re plugged them in there is a green light on the RX when it’s powered on and still the blinking green light on the esc

 

[N.Mango]

I have no idea whats going on.
But what I would do personally, is rebind the remote to the receiver.

 

[sipes190]

I have no idea whats going on.
But what I would do personally, is rebind the remote to the receiver.

Ok I will look up a video on that and try that I appreciate your time and effort

 

[N.Mango]

Ok I will look up a video on that and try that I appreciate your time and effort

Good luck, I hope it works.
Let us know.

 

[Tex Koder]

Only thing I can think of besides something is just cooked is this bullet connection I re soldered a while back could be an issue but the connection is strong and it doesn’t budge


View attachment 408099

I'm sorry..
But what the hell is that!!?

If you have bare connectors like that touching each other..

No wonder it's not working.
Caused a short circuit!

 

[N.Mango]

I'm sorry..
But what the hell is that!!?

If you have bare connectors like that touching each other..

No wonder it's not working.
Caused a short circuit!

He pulled it back to check it.

 

[Tex Koder]

He pulled it back to check it.

Pulled What back...!?
There's not enough insulation to begin with... to pull nothing back....

 

[sipes190]

I'm sorry..
But what the hell is that!!?

If you have bare connectors like that touching each other..

No wonder it's not working.
Caused a short circuit!

If you read my first post you would have read that I just striped them down to see if any had disconnected after it stopped working thanks for that comment tho if you ain’t got anything helpful then please don’t say poop