Hot racing braces,servo plate an posts,tekno Orange springs, castle fan,mud guards..It's a start, aluminum hubs an over size bearings next when available.
Talion Upgrading my Talion
- Thread starter Steveoarrma517
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, and others.
links, including eBay, Amazon, and others.
- Thread starter
- #2
No posts message from Amazon,hard to get. Any alternatives
Forgot to ask guys, aluminum wing braces an buttons. Or aluminum wing posts?. Opions?
Forgot to ask guys, aluminum wing braces an buttons. Or aluminum wing posts?. Opions?
- Thread starter
- #3
Got 7x30 servo posts finally threw eBay thanks again out there. Waiting for robotic co. To get that servo plate to me, think they were from Canada. Foot delivery? Lewis an Clark .
MrBlonde29
Member
Do you have a link for that servo plate?
- Thread starter
- #5
Found info under kraton section,CK woodie servo upgrades part list ,that is how I got to the site for plate.
MrBlonde29
Member
Awesome, thanks!
- Thread starter
- #7
I have fast Eddy bearings to replace bushings in steering rack also when stiffing up servo. Can't hurt I figure, anybody's thought on bearings.
- Thread starter
- #8
Harvesting, got my servo plate,an posts. The plate is beautiful,you can see a savox servo will drop right in.this one is a 1257 TG. Need to check an see if this one is any better than stock servo. Need to get to ace for some m 3 screw supplies,
- Thread starter
- #9
justatree
Active Member
- Messages
- 562
- Reaction score
- 215
- Arrma RC's
- Fury
does the mount for the servo (diy one) fit the stock servo?
- Thread starter
- #11
Stock servo drops into servo plate without disassembling servo. Like in other threads on forum,start all screws before tightening up.I still need to work on servo arm for level linkage.
- Thread starter
- #12
Level enough, ground off one end of post to keep servo arm level.showed with stock servo. Need servo horn to install savox servo cause I could not get screw out of stock servo.
- Thread starter
- #13
Couldn't help myself, just purchased hot racing aluminum stand for center diff.other side is aluminum soo, I figured yup.
- Thread starter
- #14
Hot racing steering rack sold out fast. Having a hard time not buying aluminum wing mount.
- Thread starter
- #15
So far have passed on aluminum wing mount untill I get a tip$ at work. So in the mean time I ordered a set of SRC road crushers.( 2 stock rims out of round,wheels wobble bad). Also ordered a t_ bone front bumper guard, cause that front end looks vunable an arrma doesn't sell rebuild shock kit.($ buy all parts seperatly$). I remember a day back when all RC cars came with front an rear bumpers. My dream RC would be all aluminum bling .Have seen other guys do this an I have always been in awe when I have. Maybe talions the one. Then I would call it the bling machine.
Tony R
Member
- Messages
- 6
- Reaction score
- 3
- Arrma RC's
- Talion
that hot racing wing mount is pretty sweet but if your going to be bashing and using it heavily for more performance I would just go with the aluminum wing posts arrma sells. It'll stiffen up the wing mount with out adding so much weight. The all aluminum wing mount is just gonna weigh the rear end down might bend upon impact eventually and (weight)will put more stress on the motor and esc but if you want a show car like you said go for it. that's just my thoughts on it though but me myself I want to go with the aluminum hubs and steering blocks as well and a servo mount but that's it I just plan on purchasing a bit of a stronger motor later to make up for the added weight.
Attachments
- Thread starter
- #17
- Thread starter
- #18
Still waiting for t-bone RC to make an send me front bumper. Wish they could send me bumper as fast as they took my money. Buying direct was a mistake, should have gone eBay or Amazon? Said they have to make it 1st, that Bologna.
- Thread starter
- #20
Got front t- bone, waiting rear,then batteries. Still trying to decide 4sor6s.
