Typhon Wider arms for Typhon 3s?

[TwinTurbo95]

Hey guys, I've got my Typhon set up for all sorts of terrain. I'm running a BLX185 with stock motor and 20t. I can run 4s with GRP's and the motor stays cool. Or I can throw on my Trencher 2.8"s and bash on 3s. I would like to make the Typhon stance a bit wider. Any ways to convert to Kraton 4s or Outcast4s or even 6s arms?

Thanks

 

[jondilly1974]

6S isn’t compatible at all. But the 4S is. You will also need the following:

Arms
Turnbuckles
Hubs
Caster blocks
Bearings
Driveshafts
Hexes
Pins
Wheel nuts
Shocks

It is a pretty long list of parts to make it about 10mm wider.

Or you could get the axles from the Granite and the HR 17mm x 10mm offset hexes and get the same results.

 

[razz007]

Hey guys, I've got my Typhon set up for all sorts of terrain. I'm running a BLX185 with stock motor and 20t. I can run 4s with GRP's and the motor stays cool. Or I can throw on my Trencher 2.8"s and bash on 3s. I would like to make the Typhon stance a bit wider. Any ways to convert to Kraton 4s or Outcast4s or even 6s arms?

Thanks

here’s a typhon 3s sporting 4s kraton/outcast arms n shocks n links n drive shafts ??

 

[slick2500]

@TwinTurbo95 I know of a set of hexes that fit but you need to drill out the pin holes to fit the Arrma pins in them. You will need 4 of these https://www.ebay.com/itm/Redcat-Rac...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649

Alternately you can buy the stuff @jondilly1974 mentioned above you need 2 sets of these https://www.ebay.com/itm/Arrma-AR31...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 then put these on https://www.ebay.com/itm/Hot-Racing...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 and it will give you 10mm more width on each side.

This used to be a 3s Typhon. All I did was add the Kraton body, side guards and center brace, it is still running Typhon arms, but I used the granite stub axles I linked above and the Hot Racing 17mm hubs.

 

[unclebrudy]

I use the Redcat Racing extensions @slick2500 linked and they are great once you drill out the holes for the stock pins. They widen the stance just about the max you would want with hub extensions vs. a complete 4S arm swap.

 

[TwinTurbo95]

Thanks guys! I ended up doing the Granite axles with the HR 10mm extenders. Looks good with 2.8" Trenchers!

 

[slick2500]

Thanks guys! I ended up doing the Granite axles with the HR 10mm extenders. Looks good with 2.8" Trenchers!

Pics or it didn't happen ?

 

[Nefarious]

Pics or it didn't happen ?

 

[sam the basher]

6S isn’t compatible at all. But the 4S is. You will also need the following:

Arms
Turnbuckles
Hubs
Caster blocks
Bearings
Driveshafts
Hexes
Pins
Wheel nuts
Shocks

It is a pretty long list of parts to make it about 10mm wider.

Or you could get the axles from the Granite and the HR 17mm x 10mm offset hexes and get the same results.

I have the pro line power strokes for the typhon 3s and want to keep them will they still work or will I have to change and if I have to change what shock do I use