Typhon Where can I get a 3D printed motor support for my stretched Typhon

[Jeppyjep]

I’m running the 4080 2022 and this thing is long ! I’d like to put a support under it . Anyone printing and selling anything that would help me ??

 

[rcastello755]

@3d-rc.myshopify.com do you?

 

[Tex Koder]

I’m running the 4080 2022 and this thing is long ! I’d like to put a support under it . Anyone printing and selling anything that would help me ??

View attachment 238267

Sure.
I can help.
Just let me know how much "gap" that's between the motor and your chassis and I'll draft up something for it.

Take into consideration that carbon side plate.. Is it directly in the way of the "gap" area under the motor?

 

[Robbbbbb66]

Sure.
I can help.
Just let me know how much "gap" that's between the motor and your chassis and I'll draft up something for it.

Take into consideration that carbon side plate.. Is it directly in the way of the "gap" area under the motor?

^^This guy will hook you up.

 

[Tex Koder]

Here's what I whipped up..

For your 4080 Motor Support

With the large bevel underneath this support -it should easily clear your side CF plate.

At 7mm base thickness, it should still give you plenty of wiggle room in case you change pinion sizes to accommodate mesh adjustments.
You can simply use double-side tape to take up any gaps between it and your chassis.

Let me know if you want me to put in a slot for zip-tie underneath (for securing it to your motor) or just leave it flush.

Your thoughts/critique?

 

[419RC]

Possibly consider being able to mount that support from underneath and wrap around the motor. This will assist in prevent side-to-side deflection as well from it pulling up. I did that with the 3s 3d printed variant thats on thingiverse.

Top pic shows the original and then i asked the creator to add the tab.

 

[Jeppyjep]

Here's what I whipped up..

For your 4080 Motor Support
View attachment 239042

View attachment 239046
With the large bevel underneath this support -it should easily clear your side CF plate.

View attachment 239044

At 7mm base thickness, it should still give you plenty of wiggle room in case you change pinion sizes to accommodate mesh adjustments.
You can simply use double-side tape to take up any gaps between it and your chassis.

Let me know if you want me to put in a slot for zip-tie underneath (for securing it to your motor) or just leave it flush.

Your thoughts/critique?

Looks great !! Thank you very much . I’m going leave it flush . Just pm me the details for delivery

 

[Moirae]

That motor is so nice in the Typhon xl.

 

[Tex Koder]

design in production >

print completed.

Specs:
Primarily designed for 4080 motor ,compatible with most 40mm cans.
Gap spacing = 7mm (edge of motor to surface of chassis)

.

 

[Jeppyjep]

design in production >
View attachment 239466

View attachment 239468

View attachment 239470

View attachment 239471
print completed.

Specs:
Primarily designed for 4080 motor ,compatible with most 40mm cans.
Gap spacing = 7mm (edge of motor to surface of chassis)

.

Came out so good . Thanks again

 

[Jeppyjep]

@Tex Koder Dudeeeee you killed it on these mounts clears my Side skirts perfectly and supports the motor perfectly. Thank you so much ! Highly recommend this guy for your 3D needs

Not to mention you had them made and shipped and I had it installed in my car exactly a week later

 

[dk3000]

@Tex Koder Awesome stuff

 

[332_RC]

Here's what I whipped up..

For your 4080 Motor Support
View attachment 239042

View attachment 239046
With the large bevel underneath this support -it should easily clear your side CF plate.

View attachment 239044

At 7mm base thickness, it should still give you plenty of wiggle room in case you change pinion sizes to accommodate mesh adjustments.
You can simply use double-side tape to take up any gaps between it and your chassis.

Let me know if you want me to put in a slot for zip-tie underneath (for securing it to your motor) or just leave it flush.

Your thoughts/critique?

What is the length on this support? When I get my Kraton slider Im looking at the TP4070, its 94.7mm long vs the 117mm 4080. Thats 22.3mm less. Looks like maybe this one would work but maybe not for the Kraton. When I get it all in front of me, that'll be some time, I'll let you know & I'll see about getting something done.

 

[Tex Koder]

What is the length on this support? When I get my Kraton slider Im looking at the TP4070, its 94.7mm long vs the 117mm 4080. Thats 22.3mm less. Looks like maybe this one would work but maybe not for the Kraton. When I get it all in front of me, that'll be some time, I'll let you know & I'll see about getting something done.

It's at 60mm at the final spec-ed version ,I believe..
I'll have to find my design file.. it's been awhile.