Ahh, you better let me take it.
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Ahh, you better let me take it.
It depends on what you want it to do, What's your intention? To make pizza cutter tires? To go 100+ MPH? Each one needs different things.It should, I can compare the dimensions to be sure.
Yeah It will.
My bad, it won't fit a firma 160a, only firma 150a and a blx 185
Just watch my last Big Rock video. The axles are necessary if you change tires and get traction a lot. So far, mine only popped apart and was able to go back together. The M2C motor mount is best because it seals dirt and doesn't bend like the other aftermarket ones. The HR Yoke is necessary in the rear. I also run a metal slipper clutch with HR aluminum slipper pads x4. Metal gears of course. I also recommend getting the ceramic hybrid from Acer Racing on the center driveshaft. I put HR pivotballs on stock rods. I run the 6s BLX system on 4s most times. I like the Granite tires pretty good.Do i need a special motor mount? will the battery fit?
Some people even said that u should change the diffs and driveshafts, but is that really necessary?
GH hooked me up with one of his 3D printed plates and my current V5 150 amp ESC fits perfecty in my BR V3 now on 6s. Well worth the minimal cost to get his plate instead of guessing at what to do with the ESC. My wife even commented “wow I bet he makes a fortune off these”...The stock 6s motor is a direct fit. The esc won't fit without modification. I have 3d printed mounts to bolt a firma 160 or a blx 185 to the original spot. PM me if your interested. I would highly recommend upgrading the diffs and driveshafts, as they will break with 6s power.
I would go with hot racing metal diffs or the arrma cnc'd diffs.
I would go with the arrma cvd slider set for the driveshafts.
You may need to upgrade the spur gear to a hot racing metal one.
Glad it works and your happy! GL with your setup!GH hooked me up with one of his 3D printed plates and my current V5 150 amp ESC fits perfecty in my BR V3 now on 6s. Well worth the minimal cost to get his plate instead of guessing at what to do with the ESC. My wife even commented “wow I bet he makes a fortune off these”...
Here is how clean of mounting the 150 esc is inside the chassis of my V3 BR (love the extra tab for the power switch);
View attachment 170045
GREAT JOB GH !!!
Yeah, i'm about to buy @StephenSchandelmayer's 6s beefcake bigrock, and I can't wait to rip it on 6s!Ok, finally picked up a matching battery to my existing 5200 mah 50c 3s so I could try the Big Rock on 6s and HOLY POW WOW KAZZOOOOWIIIEEEE!!!!
I just thought, you might want to strap down the 3 motor wires to something, so they don't bounce around. If they do, the wires will eventually fray and rip off. Same with the battery leads.GH hooked me up with one of his 3D printed plates and my current V5 150 amp ESC fits perfecty in my BR V3 now on 6s. Well worth the minimal cost to get his plate instead of guessing at what to do with the ESC. My wife even commented “wow I bet he makes a fortune off these”...
Here is how clean of mounting the 150 esc is inside the chassis of my V3 BR (love the extra tab for the power switch);
View attachment 170045
GREAT JOB GH !!!
Yeah the above photo was the initial shake down and once Im sure its how I want it, everything gets zip ties or velcro’d to “stay put”.Yeah, i'm about to buy @StephenSchandelmayer's 6s beefcake bigrock, and I can't wait to rip it on 6s!
I just thought, you might want to strap down the 3 motor wires to something, so they don't bounce around. If they do, the wires will eventually fray and rip off. Same with the battery leads.
Can you help with a fan mount anything I've seen won't work as the motor fits snugThe stock 6s motor is a direct fit. The esc won't fit without modification. I have 3d printed mounts to bolt a firma 160 or a blx 185 to the original spot. PM me if your interested. I would highly recommend upgrading the diffs and driveshafts, as they will break with 6s power.
I would go with hot racing metal diffs or the arrma cnc'd diffs.
I would go with the arrma cvd slider set for the driveshafts.
You may need to upgrade the spur gear to a hot racing metal one.
Register and gain access to Discussions, Reviews, Tech Tips, How to Articles, and much more - on the largest Arrma RC community for RC enthusiasts that covers all aspects of the Arrma-RC brand!
Register Today It's free! This box will disappear once registered!