Custom MOD Parts : Ender 3 S1 / S1 Pro

[Tex Koder]

What do you think you’ll do for the offset?

You'll have to wait and see..
But I'm wanting to bring to up to near -0.11 ,or close to it.

What type of things are you looking to adjust?

I'll reflash the firmware most likely -to add more software capabilities.

And I plan on stripping the bottom panel and try to redesign it for better & Quieter system cooling.
Along with an added Boost of higher power MOSFET to increase my bed plate heating times (and possible my hotend too.)

 

[kspitters]

You'll have to wait and see..
But I'm wanting to bring to up to near -0.11 ,or close to it.



I'll reflash the firmware most likely -to add more software capabilities.

And I plan on stripping the bottom panel and try to redesign it for better & Quieter system cooling.
Along with an added Boost of higher power MOSFET to increase my bed plate heating times (and possible my hotend too.)

Sweet! Thanks for the answers! Your brain is so smart

 

[Tex Koder]

Sweet! Thanks for the answers! Your brain is so smart

I'm just trying to keep up ,learning as I go

 

[Tex Koder]

Some simple mods:

Cable guides/wire stress relief..

This printer is so good ,it's like a box of chocolate chip muffins..!

 

[Tex Koder]

***************

 

[Tex Koder]

 

[kspitters]

View attachment 287183

View attachment 287184

View attachment 287185

View attachment 287186

View attachment 287187


***************

View attachment 287188

View attachment 287189

View attachment 287191

View attachment 287190

View attachment 287192

View attachment 287194

View attachment 287195

View attachment 287196

View attachment 287197

View attachment 287198

Sweet! Were you adjusting that belt?

View attachment 287211

View attachment 287212

View attachment 287213

What’s this? Also, tree supports are sweet!

 

[Tex Koder]

Sweet! Were you adjusting that belt?

I was looking into that portion of the gantry.. Wanting to see how the endstop sensor circuit and how it's mounted/secured in the plastic housing.

Also, for future reference, in case I want to change & create something new to add to that section of the X-axis..

For instance, if I wanted to move the filament run-out sensor to the side of the printer instead of up top (where it is now , which I strongly Dislike and think it's a Very poor design.)

What’s this? Also, tree supports are sweet!

Wait and see..

 

[kspitters]

Wait and see..

Always patience



Jokes, I’m excited!

 

[Tex Koder]

Always patience



Jokes, I’m excited!

.

 

[Tex Koder]

Hit a snag..
Was pushing it on speed and the fan shroud caught the edge of the top surface and pulled the part off /away from the supports..
It's hard to tell but the part is loose -away from the build plate...
93% complete..

Had to start again..
I slowed it down some and changed its orientation.

 

[kspitters]

View attachment 287267

View attachment 287268

View attachment 287271

View attachment 287275

View attachment 287277

View attachment 287278

View attachment 287281

Hit a snag..
Was pushing it on speed and the fan shroud caught the edge of the top surface and pulled the part off /away from the supports..
It's hard to tell but the part is loose -away from the build plate...
93% complete..
View attachment 287282

View attachment 287283


Had to start again..
I slowed it down some and changed its orientation.

View attachment 287284

View attachment 287285

View attachment 287286

View attachment 287287

View attachment 287288
View attachment 287291

View attachment 287292

View attachment 287293

Aw booo, how long was the print? Somewhere around 2-3 I’m guessing? Print looks pretty good though.

 

[Tex Koder]

Aw booo, how long was the print? Somewhere around 2-3 I’m guessing? Print looks pretty good though.

The first round that failed.. I was about 4 hours 40minutes into a 6 hour print job..

The second attempt in a different orientation & without the tree supports (with just a brim), I got it down to 5hours 15minutes..

 

[Dan B.]

What’s the grip for?

 

[Tex Koder]

What’s the grip for?

Oh you know.. Airsoft ,wink wink.

 

[Dan B.]

Yeah, don’t forget to put the red cap on the barrel.

 

[King blitz]

What’s the grip for?

Was going to ask also..

Was going to ask also..

Radio Handel? Gun Handel?
Fishing pole handle?
Walmart self check out scanner handle?
Yup it's a transmitter handle...I don't see it being for anything else ...pretty cool..nice color ..red would be better I think but that's my opinion..cause I love red

 

[Tex Koder]

So far in basic printer mods-

1. X-axis gantry rollers cover (right hand side)

2. Leadscrew coupler cover (right hand side)

3. Extruder, X-axis motor, X-axis endstop sensor cable strain relief/wires guide (left hand side)

Leadscrew coupler cover (left hand side)

 

[King blitz]

So your printing parts for your printer?

 

[Tex Koder]

So your printing parts for your printer?

Yes, at the moment it's printing/making Enhancement parts for itself..