brushless

Hi all - I posted this question on the "official" Arrma forum, but I though I'd give it a shot here too. So I had the bearing that holds the output shaft in place fail on my Fury BLX 3600KV motor. I can "wiggle" the output shaft with my fingers. Has anyone tried to rebuild their 3600KV...

Check this out: http://www.bigsquidrc.com/unboxing-arrma-110th-fury-blx-brushless-rtr/ I see the 2013 chassis side plates with a new grey chassis. But also a red battery door strap, which was discontinued (in black) for the 2011-2013 models. I have to say I like the body of the BLS models better!

A quick easy install is the Wheeliebar set for the TT MT4-G3 PD9041. I have run it on other MTs with a twgula4 wingmount. All you have to do is bend the wingmoumt apart a few mm and reem up the holes..and mount it. Here mounted on my Kraton

Hello wise men and women...I am need of some serious input... This evening during some bashing my ESC came loose...(again, look at different thread about this subject)...And ripped the connector cable of the receiver clean off...See the picture below... I know have the following questions...

Yesterday my esc decided to crap out on me. First sign was slow throttle response, then suddenly taking off or barely any throttle response. Anyway, I hooked up my leopard motor to the 80a blx esc and nothing. I hooked the 3600kv blx motor to a 60a esc and it works fine. The 80a blx esc I is...

Hi All, I want to calibrate the Fury BLX ESC. As in, setting my throttle, neutral, brake points. I have looked through the manual and I am not seeing it. Am I overlooking it? Any help would be great. Thank you!

Hello, I'm looking for an ARRMA Kraton Roller to purchase. I fully rebuilt an ERevo only to snap two of the driveshafts in about 10 minutes under the power of 6s. Due to this and my opinion of the ERevo being fragile I'd like to swap my electronics into a Kraton. Please let me know if you have...

Today I was, tinkering with the shock setup on my granite blx. I only have, ECX 1/10scale springs, soft, medium, and stiff. Well, they fit the arrma granite blx shocks! I don't know how to post links from my phone but, they're the 1/10 2wd ECX springs. I don't know how helpful this info will...

This is video is actually titled for the Durango DEX8T diff removal, but being that the Durango DEX8T and Arrma Talion are essentially the same thing (the Durango are more hopped up) I figured I'd post it here. How to remove Arrma Talion diff

Here are my two trucks: a stocks BLX and a modified MEGA. The first one has additional upgrades like: - Fastrax aluminium shocks 75mm front and 95mm aft with red extra stiff springs, 350 sct silicon oil at the moment - Savox SC-1258TG high speed all metal geared high-torque servo (not...

Anybody found some good replacements for the stock body on the Kraton? Been searching for a while and took my chance on the Pro-Line desert militia. Needs some cutting to fit the (broken) rear wing, but turned out quite nice. For sure more durable than the stock body. I know many use the...

Arrma Senton Short Course Truck Manual Arrma Senton BLX Manual Arrma Senton Media

If you're looking for even more protection for your favorite rc basher, the Arrma Kraton then look no further. T-Bone Racing now has a wide rear bumper now available! The T-Bone Racing rear Kraton bumper is extra wide to provide maximum protection and made from ultra tough nylon to provide long...

Arrma Kraton Manuals Arrma Kraton BLX Manual Arrma Kraton Parts List AR220029 - CENTRE DIFF SET 50T (1pc) S AR220033 - CVD DRIVESHAFT SET 182.5mm (2pcs) S AR220041 - F/R DIFF SET 43T SPIRAL (1pc) S AR310427 - GEARBOX CASE SET (1pc) S AR310428 - COMPOSITE CENTRE DIFF MOUNT S AR310429 - SPUR...