Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
I’d be more than happy toThey barely consume material so I don't mind making a few and you pay the shipping. Got a color preference? Got black, white, blue, purple, red, orange, glow in the dark blue, satin gold, copper, and silver, and gray I think.
The issue that comes up is how to print them successfully without a lot of hassle. When printing its done in small layers from the bottom up. So something that is tube that has a 90 degree bend in it can be difficult because all the sudden there is a ceiling with nothing to support it unless I specify that the printer build in supports to hold it up while it prints, but that adds time and material that is just thrown away later and can be difficult to remove.I was thinking, how cool it would be- if you printed one of those wicked air scoops that formula one cars have.
The amount of air the fan is moving is so low that it really doesn't matter how smooth it is, maybe if it were pushing huge air it would be better but I doubt it. I could probably take out the center cone piece and it would work a little better because less air restriction but the center cone is kinda what makes it cool lolAh that makes sense, I don't know anything about it. Just seems super cool in my head lol. Never been much of a computer person aside from basics. I still don't even know how to use my instagram, other than posting an uneditied video or picture.
I really dig the stuff you've printed in this thread, never would have occurred to me.
On the turbine scoop, would sanding the inner surfaces smooth be more efficient?
So are you telling me you have troubles printing bridges? The gps case you showed should be easy without supports provided your bridge settings are correct. I don't even have part cooling fans and can do reasonable bridges. Because I have no part cooler I have to have my bridge speed faster than usual. With a part cooler it would have to be slower. I forced myself to try to find ways to print without supports to include overhangs. I always felt it was a lot of waste both filament and extra print time.
Haha dope man. Yeah after messing with all the spektrum stuff if I could go back I'd not bother. Their documentation sucks not only for stuff that is just inaccurate but for everything when you want more details about how stuff works or even what telemetry is available or how to set it up. I hate that avc takes over aux1 and aux2 channels on the receiver when active so you lose those channels for anything else. Also the "smart throttle" throttle channel that activates automatically when used with a telemetry receiver is weird in that when you use a Y splitter to feed the throttle signal to another device (like a second ESC or in my case the ESS-One sound box) the signal is weird and basically my ESS-One can't read it. I had to do channel mixing on the DX5c to duplicate the throttle channel on Aux3 of the receiver to get the sound box signal to work on that channel instead of using the Y splitter and since the DX5c is only 5 channels that meant all 5 channels are now in use with avc active so I lost my custom horns . There a 6th channel (Aux4) on the sr6100at receiver but with the 5 channel limit of the DX5c I can't take advantage of it, sad panda. I'm still experimenting with the avc but might just disable it to get my aux channels back. If someday I want to try the MMX8s I might try pairing it with their castle telemetry adapter that converts their telemetry signal to xbus so it can be used with the telemetry spektrum radios.. but again that's $$ and honestly I don't have a good reason to do it except that I just want to try it lmao.Kudos for sticking through spektrum for the telemetry stuff. I just took delivery of a third frsky transmitter. One of them will be converted to a pistol tx so I can take advantage of the r9 system on a surface vehicle with telemetry at a fraction of the cost of the other surface systems ??
Too bad Frsky doesn't make a ground transmitter (that I know of) because I'd buy one in a heartbeat. I love my gen1 x-lite.Dang the trials you just did are above what I encountered and gave up on too easily...and that was with drones and flights controllers spektrums telemetry on the air side is just as crazy too lol.
But yeah I have a 1st gen x-lite that is just sitting around so it's perfect for a conversion. And can still do 8 channels MINIMUM with telemetry. My x-lite won't be going to ACCESS anytime soon so I can take advantage of my rx8r rx's that can still take PWM channels woot woot ?
That gimbal looks pretty sweet.So I mocked up a thing today that I think may be pretty sweet...
View attachment 88097View attachment 88098View attachment 88099
Thanks man. I forgot I had this gimbal in a box from a while ago when I was going to try to mount it on a fpv drone but it turned out to be a tad too heavy for my application. I found it again while doing some spring cleaning and thought HMMMM... maaayyybee. A 3D printed plate, cheap 4k camera, GoPro mount, mini 2s battery and a selfie stick later = Infraction gymkhana drift cam hahaThat gimbal looks pretty sweet.
Register and gain access to Discussions, Reviews, Tech Tips, How to Articles, and much more - on the largest Arrma RC community for RC enthusiasts that covers all aspects of the Arrma-RC brand!
Register Today It's free! This box will disappear once registered!