What did you break today?

[GoFastBreakFaster]

Check your straps kids!

 

[slick2500]

View attachment 188525

Check your straps kids!

At least it didn't rip them off the pack and it's a fairly easy fix.

 

[GoFastBreakFaster]

At least it didn't rip them off the pack and it's a fairly easy fix.

So that plug is replaceable?

 

[Mastaa]

So that plug is replaceable?

Yes, just look for jst-xh (balancer plugs) and make sure those loose wires are not touching meanwhile

 

[jkflow]

Something like this:
https://smile.amazon.com/Readytosky-6S-Charging-Extension-Quadcopter/dp/B06XMXQ3N4
Cut in half and solder back together, cover with heat shrink.
The order of the wires are important.

 

[GoFastBreakFaster]

@jkflow thank you sir

 

[GoFastBreakFaster]

I can't find this part without buying a front bumper. I have a skid plate and front bumper coming from RPM but where can I get this?

 

[Rcproponent]

This will do! And won’t rip again.

https://m2cracing.net/cars-and-trucks/671-m2c-3595-arrma-6s-exb-front-a-block.html

Or this:
https://www.horizonhobby.com/produc...BjG2uR1rUe2moa23Dcr95_s-GGNE4zp4aAmLCEALw_wcB

But the rpm bumper doesn’t fasten into that. Just fyi

 

[Yas]

I can't find this part without buying a front bumper. I have a skid plate and front bumper coming from RPM but where can I get this?View attachment 188681

View attachment 188678

View attachment 188679

View attachment 188680

It's the bumper mount. It comes as a 3 piece set along with the EXB bumper and bumper spring. If I were you, I'd get the aluminium standalone bumper mount from Hot Racing

This will do! And won’t rip again.

https://m2cracing.net/cars-and-trucks/671-m2c-3595-arrma-6s-exb-front-a-block.html

But the rpm bumper doesn’t fasten into that. Just fyi

Or this one! I didn't know M2C made one too

 

[GoFastBreakFaster]

I literally just found the HR mount and was about to ask about it. I noticed the rpm bumper doesn't utilize it but it is what keeps the lower arm pins in, correct?

 

[jkflow]

For the $7 extra, go with M2C and you will have no more issues and no doubt if you have the best available.

 

[Greengaunja]

This is what's needed for RPM:

Not sure of part number.

 

[crimsonfancy]

these

 

[JSmalls87]

Slid too hard into a metal pole on my outcast 4s...ouch. Thanks to JRC and a bunch of spare parts laying around this won't be too expensive to fix

 

[slick2500]

This is what's needed for RPM:View attachment 188725View attachment 188726

Not sure of part number.

From what I understand the RPM front bumper now comes with a thingy to hold the pins in the front.

 

[morrjr71]

From what I understand the RPM front bumper now comes with a thingy to hold the pins in the front.

It does, but it's a thin plastic piece that goes in front of the stock aluminum front lower hinge pin mount. They give you two with the bumper, which makes it look to me like it is a high failure part. I use the RPM bumper, but I replaced the entire stock front hinge pin mount with the Hot Racing lower front/front hinge pin mount (see below). The HR part works great with the RPM bumper.

https://www.amazon.com/gp/product/B07MC5JFLX/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

 

[slick2500]

It does, but it's a thin plastic piece that goes in front of the stock aluminum front lower hinge pin mount. They give you two with the bumper, which makes it look to me like it is a high failure part. I use the RPM bumper, but I replaced the entire stock front hinge pin mount with the Hot Racing lower front/front hinge pin mount (see below). The HR part works great with the RPM bumper.

https://www.amazon.com/gp/product/B07MC5JFLX/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

I know I have all of their suspension mounts.

 

[morrjr71]

I know I have all of their suspension mounts.

And I will someday. I expect to get the HR gearbox for the rear soon, and I will replace the rear/front hinge pin mount when I do that. I'm not as concerned about the front/rear, so that may come later.

From what I understand the RPM front bumper now comes with a thingy to hold the pins in the front.

Here's link to the latest version of the RPM bumper. It shows the small piece that holds the hinge pins in.

https://www.rpmrcproducts.com/shop/bumpers/front-bumpers/kraton-6s-front-bumper/

 

[gotnitro]

I broke my A$$ from eating an Italian beef sangweech with special HOT giardiniera peppers I grew last summer.. Them bitches were stupid hot!!.. At the time it seemed like a great idea! My stomach said hellzz yeah while my A$$ has a different story.

Another note to self, listen to A$$ next time!

 

[Greengaunja]

It does, but it's a thin plastic piece that goes in front of the stock aluminum front lower hinge pin mount. They give you two with the bumper, which makes it look to me like it is a high failure part. I use the RPM bumper, but I replaced the entire stock front hinge pin mount with the Hot Racing lower front/front hinge pin mount (see below). The HR part works great with the RPM bumper.

https://www.amazon.com/gp/product/B07MC5JFLX/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

Yeah I have this too. However there is still a gap for the plastic end piece at the bottom. I want to close it off because I increased bulkhead strength with a slightly wider bore and longer bolt fastening RPM bumper, Hot Racing skid plate, and bulkhead to the chassis and tightened it all up.

And I will someday. I expect to get the HR gearbox for the rear soon, and I will replace the rear/front hinge pin mount when I do that. I'm not as concerned about the front/rear, so that may come later.

Here's link to the latest version of the RPM bumper. It shows the small piece that holds the hinge pins in.

https://www.rpmrcproducts.com/shop/bumpers/front-bumpers/kraton-6s-front-bumper/

The bulkhead/gearbox is the only HR part I don't have that can possibly be installed on my Senton. Haven't seen a need for it yet as the bulkhead covers and the way I've secured the bulkheads strengthened up the composite bulkhead beyond my expectations.